Celec Enterprises
Ludhiana, Punjab
GST No. 03AAJPC2602H1ZG
TrustSEAL Verified
Call 08048706651
88% Response Rate
SEND EMAIL
Product Details:
| Minimum Order Quantity | 5 Piece |
| Brand | Celec |
| Relay Contacts | 7 Amp 250 VAC |
| Display Size | 1.00" LED Display |
| Power Factor Control Range | From 1% to 120% of rated current. |
| Switching Time Setting On Delay | 1 to 60 seconds |
| Weight | 1 Kg |
| Dead Band Setting | 0.01 - 0.20 |
| Ampere Sensitivity Setting | 1 to 20 A |
| Switching Type | Binary FIFO |
| CT Ratio Programming | Up to 2000 A |
| Dimensions | 144mm (W) x 144mm (H) x 67mm (D) |
| Voltage Input | 240 VAC (110V,415V against order) |
| Bezel/Panel Cut Out | 90 mm x 90 mm +/- 1 mm |
| Current Input | 10mA to 5.00 Amp (Isolated) |
| Frequency | 45 - 65 Hz |
| Operating Temperature | 10 Degree to 70 DegreeC |
| No of Channels | 6 |
6 steps Power Factor Controller 240V 63PFC i s used, where the power factor load fluctuates greatly with variation. It check as shown above measurement of the power factor with set desired power factor and if it less than it gives the command to switch one step capacitor unit to get the desired set of power factor.
if examined power factor is more than set value of power factor, then it gives the command to switch off connected capacitor steps until unless it reaches the desired set of power factor value.
In the panel, capacitors are connect and disconnect automatically with the help of automatic power factor correction relay.
APFC Relay use to automate capacitor bank and one of the most difficult roles in place where high and controlled amount of electricity is applicable.
This includes large factories or industries or schools or colleges.
APFC Relay is especially necessary for colleges; because students are learn on the basis of the various types of voltage and ampere fluctuations in practical labs.
However, all relays cannot be to accurate and therefore, there is a need of a very accurate and precise control relay.
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Piece |
| Brand | Celec |
| Voltage Input | 350 to 460 VAC (110V,220V against order) |
| Target Power Factor Setting | 0.90 lag to 0.90 lead |
| Power Factor Control Range | From 1% to 120% of rated current. |
| Switching Time Setting ((b) Off Delay ) | 1 to 60 seconds |
| Dead Band Setting | 0.01 to 0.20 |
| Ampere Sensitivity Setting | 1 to 20 A |
| Switching Type | Binary |
| CT Ratio Programming | Up to 2000 A |
| Dimensions | 144 mm (W) x 144 mm (H) x 67 mm (D) |
| Relay Contacts | 7 Amp 230 VAC |
| Bezel/Panel Cut Out | 140 mm x 140 mm +/- 1mm |
| Current Input | 10 mA to 5 A |
| Weight | 1 Kg |
| Frequency | 45 - 65 Hz |
| Operating Temperature | 10 to 50 Degree Celsius |
| Display Size | 1.00 inch |
| Stages | 16 |
Additional Information:
Product Details:
| Minimum Order Quantity | 5 Piece |
| Voltage | 240 VAC (110V,415V against order) |
| Model Name/Number | 93 PFC-6-Channels |
| Brand | Celec |
| Relay Type | APFC Relay |
| Frequency | 45 to 65 Hz |
| Operating Temperature | 10 Degree to 70 DegreeC |
| Country of Origin | Made in India |
| Weight | 1 Kg. |
| Switching Type | Binary |
| Display Type | Digital |
| Display Parameters | PF,kVA,kVAr,Volt,Amp.,KW |
if examined power factor is more than set value of power factor, then it gives the command to switch off connected capacitor steps until unless it reaches the desired set of power factor value.
In the panel, capacitors are connect and disconnect automatically with the help of automatic power factor correction relay.
Additional Information:
Product Details:
| Minimum Order Quantity | 5 Piece |
| Brand | Celec |
| Voltage Input | 415 VAC (110V,220V against order) |
| Manual Operation | Selectable |
| Display Parameters | PF,kVA,kVAr,Volt,Amp.,KW |
| Dimensions | 96 mm (W) x 96 mm (H) x 87 mm (D) |
| Relay Contacts | 7 Amp 230 VAC |
| Bezel/Panel Cut Out | 90 mm x 90 mm +/- 1 mm |
| Current Input | 10 mA to 5.00 A |
| Weight | 0.7 Kg |
| Frequency | 45 - 65 Hz |
| Operating Temperature | 10 to 50 Degree Celsius |
| Display Size | 0.56 inch |
| Power Factor Control Range | From 1% to 120% of rated current. |
| Target Power Factor Setting | 0.90 lag to 0.90 lead |
| Switching Time Setting ((b) Off Delay) | 1 to 60 seconds |
| No of Channel | 8 |
| Dead Band Setting | 0.01 to 0.20 |
| Ampere Sensitivity Setting | 1 to 20 Amp |
| Switching Type | Binary |
| CT Ratio Programming | Up to 2000 A |
Additional Information:
Product Details:
| Minimum Order Quantity | 5 Piece |
| Brand | Celec |
| Weight | 1 Kg |
| Dead Band Setting | 0.01 to 0.20 |
| Ampere Sensitivity Setting | 1 to 20 A |
| CT Ratio Programming | Up to 2000 A |
| Switching Type | Binary |
| Manual Operation | Selectable |
| Relay Contacts | 7 Amp 230 VAC |
| Display Parameters | PF,kVA,kVAr,Volt,Amp,KW |
| Dimensions | 144 mm (W) x 144 mm (H) x 67 mm (D) |
| Voltage Input | 240 V (110 V,220 V ) |
| Bezel/Panel Cut Out | 140 mm x 140 mm +/- 1mm |
| Frequency | 45 to 65 Hz |
| Current Input | 10 mA to 5.00 A |
| Operating Temperature | 10 to 70 Degree Celsius |
| Stages | 8 Stages |
| Display Size | 1 inch |
| Target Power Factor Setting | 0.90 lag to 0.90 lead |
| Power Factor Control Range | From 1% to 120% of rated current. |
| Switching Time Setting ((b) Off Delay) | 1 to 60 seconds |
Additional Information:
Product Details:
| Minimum Order Quantity | 5 Piece |
| Application | Power Factor correction |
| Voltage | 230V |
| Current | 5 Amp |
| Brand | Celec |
| Ampere Sensitivity Setting | 1 to 20 A |
| Dead Band Setting | 0.01 to 0.20 |
| Dimensions | 144 mm (W) x 144 mm (H) x 67 mm (D) |
| Display Size | 1.00 inch |
| Power Factor Control Range | From 1% to 120% of rated current. |
| Relay Contacts | 7 Amp 230 VAC |
| Weight | 1 Kg |
| Bezel/Panel Cut Out | 140 mm x 140 mm +/- 1 mm |
| CT Ratio Programming | Up to 2000 A |
| Current Input | 10 mA to 5.00 A |
| Frequency | 45 - 65 Hz |
| No of Channel | 12 |
| Operating Temperature | 10 to 50 Degree Celsius |
| Switching Time Setting ((b) Off Delay) | 1 to 60 seconds |
| Switching Type | Binary |
| Target Power Factor Setting | 0.90 lag to 0.90 lead |
| Voltage Input | 240 V |
Additional Information: